Boyt Secure Vault 33013 Manual Transmission
Vault keys override the safes electronic operating system and can be used to access. OPENING THE SAFE FOR THE FIRST TIME: To open the safe for the first.
1 Secure Vault Select Low Profile Handgun Safe • Secure storage for handguns and valuables with high-tech digital locking system • Incorrect entry lockout and hidden commercial cylinder key override • Heavy-duty 11-gauge steel door opens in front and has a 15-gauge steel body • Features keyless entry with 1,000 different electronic push-button code combinations • Steel cross bolts for additional protection of firearm and valuables • Predrilled holes for mounting in trunk or on wall • California DOJ approved • Interior: 13' x 16.75' x 8' • Exterior: 13.75' x 17' x 8' Boyt Harness Company SKUs.
Read Instructions%20for%202011.pdf text version Secure Vault Model 33013 NOTICE MOUNTING YOUR SECURE VAULT TO FLOOR OR WALL: The vault that you have just purchased is designed to be mounted to something sturdy (i.e. Shelf, wall, etc.) for proper safety. It is NOT designed to be used as a carrying case. Kurtai atlasi tochigi 2017.
If this case is dropped, it could possibly cause the opening mechanism to trigger. It contains pre-drilled holes for ease of mounting. It is recommended that you use screws to mount the vault from the inside. If you have any questions about proper mounting, please contact our customer service department at 1-800-550-2698. KEY OPENING OF THE SECURE VAULT: The Secure Vault is supplied with two keys to open it manually. Do not store your keys inside the safe. Secure Vault keys override the safes electronic operating system and can be used to access the vault at any time; so it's important to store your keys in another location.
INSTALLING BATTERIES: Open the Secure Vault to access the battery holder located in the top of the vault, under the foam lining and behind the locking mechanism. Remove the thumbscrews on each end of the battery holder. Install eight AA alkaline batteries as instructed on the face of the holder, we suggest using Duracell or Energizer brands.
Reinstall the battery holder with the batteries. Be careful not to pinch the wires. Non phixion the green cd zip download. FACTORY PRE-SET CODE: The Secure Vault has a pre-set access code.
To open your Secure Vault after you have put in your eight AA alkaline batteries, press the push buttons: 1, 2, 3, 4, 1 in sequence left to right. Once you program your vault with your personal five-digit code the factory pre-set code is no longer operational. PROGRAMMING: With the door open, find the black programming push button located behind the locking mechanism inside the top of the Secure Vault. This is a small button, approximately 1/16'. While holding this button in, program your five digit combo.
Release the reset button. Repeat again.
ENTERING THE WRONG COMBINATION: If four wrong entries are entered, a continuous beep will be heard. To reset your vault you must open it manually with your key, remove the batteries and allow the safe to power down for 30 minutes. Re-install batteries, and use the programming instructions above to re-program your safe.
Secure Vault Model 33013 9V BATTERY 'JUMP START' FEATURE: If you lose battery power you have the option of using the 9V jump feature to open your safe or you can use your key. To use the 9V feature hold a 9Vbattery to the battery contacts on the outside of the safe. Be sure to align the battery properly.
Align the smaller (+) battery contact with the smaller contact on the safe, and the larger () battery contact with the larger contact on the safe. While holding the 9V battery in place enter the factory pre-set code 1, 2, 3, 4, 1. Note, the 'jump start' feature only works while the safe is un-powered, if the batteries in the safe are charged, the 'jump start' feature will not work. KEY REPLACEMENT: Should you misplace your keys, you may order a replacement by writing to the address below or by calling our customer service department. Your key code number is located on the key lock face; this number will be required for replacement. Replacement cost is $10.00 per key.
WARRANTY: Secure Vault safes are protected by a full one-year guarantee that entitles the buyer to free repair if the product failure was caused by a defective part or faulty workmanship. This guarantees lasts for one year from the date of purchase. Claims require an original receipt as proof of purchase and are processed directly through Secure Vault by calling customer service at 1-800-550-2698. TROUBLESHOOTING GUIDE: Problem Safe beeps constantly. Cause An incorrect access code has been entered three times in a row and the safe is now in 'lock out' mode. Solution The buzzer will sound for three minutes during which time you can use the manual key to open the safe and press the programming key to reset the safe, see instructions. After the three minutes the buzzer will stop and you can again try to access the safe using your personal fivedigit access code.